Download Labeldownload
Olympus 70% Water Dispersible Granular Herbicide
CROP PROTECTION

Olympus 70% Water Dispersible Granular Herbicide

Herbicide
Olympus® is a cost-efficient, effective power-up herbicide for grass control in spring and winter wheat.
Approved In
AR, CO, IA, ID, IL, IN, KS, KY, LA, MI, MN, MO, MS, MT, ND, NE, NM, NV, OH, OK, OR, SD, TN, TX, UT, WA, WY
    Group NumberFormulaRegistration Number
    GROUP PROPOXYCARBAZONE-SODIUM HERBICIDE dry0000264-00809-AA-0000000
    Active IngredientFormulation
    Propoxycarbazone-sodium70 %
Labels / MSDS
Use and Mixin

Use and Mixing

The instructions for use and mixing described below are from the Environmental Protection Agency approved Federal Label. Always read and follow label instructions. Not all products are registered for use in every state. Please check with Bayer or your local Lead State Agency for product registration status. If you wish to find out if a product is registered in your state or for additional product information, send us an email or call 1-866-99-BAYER.
      MIXING INSTRUCTIONS
      MIXING INSTRUCTIONS Ensure the spray tank is clean. In-line strainers and nozzle screens should be clean and 50 mesh or coarser. 1. Fill the spray tank 1/4 to 1/2 full with clean water and begin agitation or bypass. 2. Add the appropriate rate of OLYMPUS 70% WATER DISPERSIBLE GRANULAR HERBICIDE, as determined under "Recommended Rates", directly to the spray tank. Maintain sufficient agitation during both mixing and application. 3. Add the broadleaf weed herbicide. 4. Add the surfactant. 5. Fill the spray tank with balance of water needed. 6. Maintain sufficient agitation during both mixing and application of OLYMPUS 70% WATER DISPERSIBLE GRANULAR HERBICIDE. RE-SUSPENDING WG PRODUCTS IN SPRAY SOLUTION OLYMPUS 70% WATER DISPERSIBLE GRANULAR HERBICIDE may settle if left standing without agitation. If the spray solution is allowed to stand for one hour or more, re-agitate the spray solution for a minimum of 10 minutes before application.
      Reentry PPE
      PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is long-sleeved shirt and long pants, socks, shoes, chemical-resistant gloves made of any waterproof material and protective eye wear.
      PPE
      PERSONAL PROTECTIVE EQUIPMENT (PPE) Applicators and other handlers must wear: - Long-sleeved shirt and long pants - Waterproof gloves - Shoes plus socks Follow manufacturer's instructions for cleaning and maintaining PPE (Personal Protective Equipment). If no such instructions for washables, use detergent and hot water. Keep and wash PPE separately from other laundry.
      Tankmix Compatibility
      COMPATIBILITY If OLYMPUS 70% WATER DISPERSIBLE GRANULAR HERBICIDE is to be tank mixed with other herbicides, compatibility should be tested prior to mixing. To test for compatibility, use a small container and mix a small amount (0.5 to 1qt) of spray solution, combining all ingredients in the same ratio as the anticipated use. If any indications of physical incompatibility develop, do not use this mixture for spraying. Indications of incompatibility usually occur within 5-15 minutes after mixing. Read and follow the label of each tank mix product used for precautionary statements, directions for use, geographic and other restrictions. Indications of incompatibility include separation in the mix, and either clumping or clabbering of the mixture. TANK CLEANUP PROCEDURE 1. Drain the tank completely, and then wash out tank, boom and hoses with clean water. Drain again. 2. Half fill the tank with clean water and add ammonia (i.e., 3% domestic ammonia solution) at a dilution rate of 1% (i.e., 1 gallon of domestic ammonia for every 100 gallons of rinsate). Complete filling of the tank with water. Agitate/recirculate and flush through boom and hoses. Leave agitation on for 10 minutes. Drain tank completely. 3. Repeat step 2. 4. Remove nozzles and screens and soak them in a 1% ammonia solution. Inspect nozzles and screens and remove visible residues. 5. Flush tank, boom, and hoses with clean water. 6. Inspect tank for visible residues. If present, repeat step 2.

Recommended Agronomy Resources

Featured
ARTICLE

Fighting Back Against Prolific Weed Resistance

Featured
ARTICLE

Bayer PLUS Rewards 10% Rewards Features

Featured
ARTICLE

Top 10 Tips For Corn Yields

Seed Brands & Traits
Crop Protection
Tools
Bayer
Disclaimer

Always read and follow pesticide label directions, insect resistance management requirements (where applicable), and grain marketing and all other stewardship practices.

Follow Us

©2024 Bayer Group. All rights reserved.